Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Burbank, CA
Gate work in Burbank is different from what we see in most of Los Angeles County. The mix of 1940s-era ranch homes with original iron gates, plus the hillside estates climbing into the Verdugo Mountains, means two very different jobs often sit a mile apart. Hot summers, Santa Ana winds, and irrigation overspray all take a toll on operators, hinges, and steel. Portcullis Gate Repair serves Burbank homeowners with a written price before any work starts and a 365-day written guarantee on every repair. Call us at (669) 800-5686 and you’ll reach a live person, any hour.
Why Burbank Homes Are Different
Burbank’s housing stock tilts heavily toward single-family ranch homes built between the 1940s and 1960s. Many of those properties still have their original iron or chain-link gates. The iron work that survived has usually spent decades getting hit by sprinkler overspray, and the hard water in this area accelerates rust on hinges, latch posts, and the lower rail of the gate frame. We regularly see gates where the bottom hinge has corroded into the post, and the gate sags enough to drag across the driveway.
Then there are the hillside properties. In neighborhoods above Kenneth Road, we work on gates set into slopes that run 25 to 30 degrees or steeper. A standard automatic opener mounted on that kind of grade will often strip its gears within a year because it’s fighting gravity every time it cycles. Those installations need a torque limiter and, in many cases, an engineer-stamped plan before the city will sign off. Burbank’s hillside construction codes are strict, and for good reason: seismic retrofitting and fire access both depend on a gate that opens reliably when it has to. Wrought iron on a steep slope is not a place for shortcuts.
Climate matters here too. Dry summer heat causes gate operators to overheat, particularly units mounted in direct afternoon sun on a west-facing wall. Wood gates dry out and warp, which throws off the latching geometry. When the Santa Anas blow through, fine dust gets into operator internals and limit switches. A gate that worked fine in May can fail in September because the operator’s thermal protection keeps tripping. Knowing which failures are seasonal and which are structural is part of what makes local experience useful.
Styles & brands we work with
Our Main Burbank Services
Most calls from Burbank fall into two buckets: a gate that has stopped working and needs repair, and an old or failing gate that needs replacing. Electric gate repair sits close behind, since a surprising number of Burbank homes already have an opener on a driveway gate. Each service has its own Burbank page with local pricing and details.
Gate Repair in Burbank
We repair swing gates, sliding gates, and pedestrian gates across Burbank. The most common job here is a gate that sags and drags, usually because the hinge side has rusted or the post has shifted. On hillside properties, we also see failed opener brackets and bent actuator arms where the operator has been fighting the slope. Every repair starts with an assessment of what failed and why, and you get a written price before a single bolt comes out. Gate Repair in Burbank covers costs, same-day availability, and the 365-Day Done Right Promise.
Gate Installation in Burbank
New gate installation in Burbank frequently involves more than swapping an old gate for a new one. The post footings may need to be redone, the opening may not be square, and on hillside lots the city may require an engineer-stamped plan before installation. We handle the full job: removal of the old gate, post setting, steel or wood gate fabrication to spec, and operator mounting when you want automation. You’ll get a measured, written price before any work begins. Gate Installation in Burbank has full details and local pricing.
Electric Gate Repair in Burbank
Electric gate repair in Burbank means diagnosing the operator, the control board, the safety loops, and the power supply. Heat exposure and Santa Ana dust both shorten operator life here, and we see a steady run of failed limit switches and burned-out capacitors. Our technicians service nine major operator brands, so the tech who arrives already knows your system. Wiring, safety edges, and programming are not jobs to hand to a generalist. Electric Gate Repair in Burbank walks through costs, common failures, and what a repair visit includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Burbank
We carry parts locally for the operators Burbank homeowners run most often: FAAC, BFT, Linear, and Viking, among others. Stocking boards, arms, and limit switches near the service area means most repair calls in Burbank are completed the same visit. See our brands for the full list we service.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Burbank, CA
| Service | Typical Range in Burbank |
|---|---|
| Swing gate actuator swap | $480 – $850 parts and labor |
| Sliding gate operator replacement | $650 – $1,150 parts and labor |
| Hinge replacement (welded steel pair) | $180 – $350 parts and labor |
| Post replacement (single) | $350 – $700 parts and labor |
| Control board replacement | $220 – $450 parts and labor |
| Safety loop sensor repair or replacement | $190 – $380 parts and labor |
| Gate sag correction and frame realignment | $250 – $550 parts and labor |
| Full gate installation (steel, single swing) | $1,800 – $4,500 measured and installed |
| Full gate installation (sliding, driveway) | $2,500 – $6,500 measured and installed |
| Operator-only installation (labor) | $450 – $900 installed |
Hillside work in Burbank pushes prices toward the upper end of these ranges. A steep slope often means longer post footings, torque limiters on the operator, and sometimes an engineer-stamped plan and permit before installation can start. Whatever the job, the price is set in writing before work begins. If the repair fails inside 365 days, we return and correct it at no charge.
Neighborhoods We Serve in Burbank
We run calls across Burbank, from the flat ranch-home streets near the airport to the hillside lanes above Kenneth Road. Most repair calls in the valley floor are reached the same day, and hillside properties are scheduled on the next available window with a real arrival time given in advance.
- Magnolia Park
- Rancho Adjacent
- Burbank Hills above Kenneth Road
- Toluca Woods border
- Verdugo Mountains foothills
Service Area – Cities Near Burbank
While this page covers Burbank specifically, we also serve homeowners in nearby communities. If you’re on the edge of our service area, you’ll find local pages for Campbell, CA, Boulder Creek, CA, Saratoga, CA, and San Jose, CA. Dispatch and scheduling for Burbank jobs are coordinated through our Los Angeles office, with crews serving Burbank locally.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Burbank
Most Burbank repair calls in the valley floor can be reached the same day. Hillside properties get a real arrival window, not a four-hour guess. Call (669) 800-5686 and a live person will tell you exactly when a technician can be there.
Many standard repairs do not require a permit. Hillside installations and any job involving new footings or significant structural changes often do, and Burbank’s hillside codes can require an engineer-stamped plan. We’ll tell you at the estimate whether a permit applies to your job.
Every repair carries a written guarantee for 365 days. If the same repair fails inside that period, we return and fix it at no charge. The guarantee is stamped on the invoice, not promised over the phone.
If your gate is sagging, stuck, or refusing to open, call Portcullis Gate Repair at (669) 800-5686 for a free estimate. You’ll get a written price before any work starts, and a live person answers around the clock.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Hinge sheared off our heavy iron gate. They welded a new one on and it's sturdier than before. Showed up on time and cleaned the driveway after the welding."
- Rhonda Mikula"Our intercom and gate motor both quit. They fixed the whole system in one visit and explained the warranty clearly. On time, polite, and tidy. Can't ask for more."
- Yvette Marchetti"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw